Same Size Is Not an Approved Substitute: A Structural-Repair Fastener Checklist
A structural repair fastener should not be replaced simply because an alternative has the same diameter, length or nominal strength grade. In automotive body repair, the fastener is part of an engineered joint that may also depend on the mating materials, hole geometry, rivet deformation, adhesive system and installation tooling. Before accepting a substitute, repair planners and procurement teams must verify the vehicle-specific OEM repair procedure and obtain the required approval.

Table of Contents
- Why Same Size Does Not Mean Equivalent
- What Makes an Automotive Structural Fastener Different?
- Six Factors to Check Before Accepting a Substitute
- OEM Part vs Replacement Candidate: Comparison Matrix
- A Practical Fastener Substitution Approval Workflow
- Supplier RFQ and Documentation Checklist
- Receiving Inspection and Nonconformance Handling
- Frequently Asked Questions
1. Why Same Size Does Not Mean Equivalent
When a structural repair fastener becomes unavailable, purchasing teams may look for an alternative with matching dimensions and similar mechanical properties.
This can be a useful starting point for commercial identification, but it is not sufficient for structural repair approval.
A fastener’s suitability depends on more than its outside diameter or material strength. Its geometry, material, installation behavior, mating components and compatibility with the original repair procedure can all affect the completed joint.
This issue is particularly relevant to modern vehicle body structures, which can combine different grades of steel, aluminium components, structural adhesives and multiple mechanical joining methods.
For example, a replacement blind rivet may have a similar nominal diameter to the original component but a different head profile, grip range, mandrel design or deformation behavior.
These differences may affect how the rivet forms and interacts with the connected materials.
The Tesla 2025+ Model Y Collision Repair Procedures Manual specifies the use of fasteners listed in its approved structural-repair fastener information.
Similarly, Ford’s October 2025 collision position statement identifies vehicle-specific structural rivets, adhesives and installation tools as part of its approved repair approach. It explains that non-approved structural fasteners have not been validated for those repair applications.
These are manufacturer-specific requirements, not universal instructions for every vehicle brand.
The practical lesson is clear:
Dimensional similarity establishes a candidate for review. It does not establish engineering equivalence or OEM approval.
2. What Makes an Automotive Structural Fastener Different?
Structural fasteners are selected as part of a complete joining system.
Depending on the original vehicle design and repair procedure, this may include:
- Self-piercing rivets (SPR).
- Blind structural rivets.
- Solid rivets.
- Flow-drill screws (FDS).
- Specific structural bolts and nuts.
- Approved structural adhesives used together with mechanical fasteners.
These components do not all work in the same way.
2.1 Fastener Geometry
Important geometric features can include:
- Head diameter and head profile.
- Body diameter and overall length.
- Grip range.
- Mandrel configuration.
- Material thickness compatibility.
- Installation depth and formed geometry.
For rivets, the finished joint depends on how the fastener deforms during installation.
Two rivets with similar outside dimensions may not produce the same installed geometry.
2.2 Material and Mechanical Properties
The fastener material must be considered together with the connected materials and original joining requirements.
For example, an aluminium structural rivet and a steel structural rivet are not interchangeable simply because their nominal dimensions match.
Relevant information may include:
- Base material and grade.
- Mechanical properties specified by the OEM.
- Corrosion protection.
- Compatibility with mating materials.
- Required surface condition.
Do not infer material equivalence from appearance or a general strength designation.
2.3 Installation Tool and Process
The installation method is another critical part of the specification.
A structural rivet may require a particular installation tool, nosepiece, mandrel or process setting.
The tool and fastener combination can influence the finished installation geometry.
A replacement component that cannot be installed using the specified equipment should not be accepted merely because it can physically enter the original hole.
3. Six Factors to Check Before Accepting a Substitute
Before evaluating a replacement candidate, review the following six areas.
| Review Factor | What to Compare | Why It Matters |
|---|---|---|
| OEM part identification | Original part number, revision and repair location | Confirms the intended component |
| Dimensions and geometry | Diameter, length, head profile, grip range and other specified features | Establishes physical compatibility |
| Material | Material grade, composition and mechanical requirements | Helps identify material differences |
| Surface condition | Coating, finish, corrosion protection and compatibility | Prevents unreviewed changes to the original surface system |
| Installation system | Tool, mandrel, nosepiece and specified installation method | Determines whether the approved process can be followed |
| Repair approval | Applicable OEM procedure, approved parts list and documented deviation approval | Establishes whether the proposed replacement is permitted |
The six-factor matrix is a purchasing and engineering review tool developed for this article. It does not replace an OEM parts list or technical approval.
3.1 Check the Original Part Number First
The original OEM part number is the most useful starting point.
Record:
- Vehicle manufacturer.
- Model and production range.
- Repair location.
- Original part number.
- Applicable repair manual and revision.
- Any listed replacement or superseding part number.
A part number change should be checked against the manufacturer’s official replacement information rather than assumed to be a direct substitution.
3.2 Compare the Complete Geometry
Do not compare only the nominal diameter.
For a rivet, the review may need to include head dimensions, body geometry, grip range, mandrel characteristics and the installed configuration.
For a structural bolt, the review may need to include thread, head design, length, material, mating nut and washer requirements.
The original drawing and approved repair procedure determine which dimensions are critical.
3.3 Verify the Installation System
A fastener and its installation tool should be reviewed together.
For example, the Ford October 2025 position statement discusses location-specific structural rivets, mandrels and installation tools.
This illustrates why a generic rivet gun and a visually similar replacement rivet cannot automatically be assumed to reproduce the original joining process.
Read the actual OEM procedure for the vehicle and repair location before accepting an alternative.
4. OEM Part vs Replacement Candidate: Comparison Matrix
A comparison sheet makes technical differences visible before purchasing commits to a replacement.
Use this example as a blank working template.
| Specification | Original OEM Fastener | Proposed Replacement | Review Status |
|---|---|---|---|
| OEM part number | To be confirmed | To be provided | Open |
| Product type | To be confirmed | To be provided | Open |
| Diameter | Drawing value | Candidate value | Pending verification |
| Overall length | Drawing value | Candidate value | Pending verification |
| Head geometry | OEM drawing | Candidate drawing | Pending verification |
| Grip range | OEM requirement | Candidate specification | Pending verification |
| Material | OEM specification | Candidate material | Pending verification |
| Mechanical requirements | OEM requirement | Candidate test data | Pending verification |
| Surface finish | OEM specification | Candidate finish | Pending verification |
| Installation tool | OEM-approved tool | Proposed tool | Pending verification |
| Repair procedure | Current OEM document | Applicable procedure | Open |
| Approval evidence | OEM reference | Approval or deviation reference | Open |
Use four possible review outcomes:
- Matched: The available information matches the specified requirement.
- Different: A technical difference has been identified.
- Unknown: Supporting information is missing.
- Approval Required: A responsible OEM or engineering decision is needed.
A blank field must not be treated as a match.
Why a Matching Strength Grade Is Not Enough
Two fasteners with similar strength designations may still differ in:
- Material chemistry.
- Heat-treatment condition.
- Ductility.
- Surface treatment.
- Head or shank geometry.
- Installation behavior.
- Approved application.
Mechanical strength is only one part of a structural joining specification.
The same principle applies to rivets: matching the nominal diameter does not establish equivalent joint performance.
5. A Practical Fastener Substitution Approval Workflow
When an original structural fastener is unavailable, use a controlled decision process rather than moving directly from quotation to installation.
Stage 1: Identify the Original Requirement
Collect the vehicle identification or applicable production information, repair location, OEM part number and current repair procedure.
If the original part number cannot be identified, keep the substitution request open.
Stage 2: Obtain the Candidate Specification
Ask the proposed supplier for:
- Product drawing.
- Dimensions and tolerances.
- Material and grade.
- Surface finish.
- Relevant mechanical test information.
- Installation requirements.
- Product identification and traceability information.
For structural rivets, include the relevant mandrel and installation tool information.
Stage 3: Document Every Difference
Compare the original and proposed fasteners.
Do not hide a difference because the two products have similar dimensions.
Record missing data, deviations and assumptions separately.
Stage 4: Request Authorized Technical Review
Submit the comparison to the vehicle OEM or the authorized engineering party responsible for the repair.
The review should establish whether the candidate is permitted for the specific vehicle, connection and repair procedure.
A supplier’s technical opinion or a generic test report cannot independently replace this approval.
Stage 5: Control the Purchasing Decision
Only proceed according to the documented approval and procurement requirements.
If approval is not available, keep the candidate on hold.
Do not instruct the repair technician to install an unapproved substitute.
Stage 6: Preserve the Approval Record
Retain:
- Original part identification.
- Candidate part identification.
- Comparison sheet.
- Supporting drawings and documents.
- Approval or deviation reference.
- Purchase order and batch identification.
- Applicable receiving inspection records.
This creates a traceable record connecting the original requirement with the supplied component.
6. Supplier RFQ and Documentation Checklist
A good RFQ should explain that the enquiry concerns an automotive structural-repair application.
A general request for a high-strength rivet or bolt is not sufficient.
Information to Include in the RFQ
| RFQ Field | Required Information |
|---|---|
| Application | Vehicle body structural repair or specified assembly |
| Vehicle information | Manufacturer, model and applicable production range |
| Original part | OEM part number and available identification |
| Repair location | Specific joining position or reference drawing |
| Product type | SPR, blind structural rivet, solid rivet, FDS or structural bolt |
| Dimensions | Diameter, length, head geometry and other specified dimensions |
| Material | Required material grade and mechanical properties |
| Surface treatment | Original finish and required corrosion protection |
| Mating components | Material type, thickness and assembly arrangement |
| Installation system | Tool, mandrel and process requirements where applicable |
| Quantity | Required quantity and packaging details |
| Inspection | Dimensional, material and other specified inspection requirements |
| Documentation | Drawing, certificate, inspection report and traceability requirements |
Documents to Request from the Supplier
Depending on the specific product and purchase specification, relevant documents may include:
- Product drawing and revision.
- Material identification or certificate.
- Dimensional inspection report.
- Mechanical test information where applicable.
- Surface-treatment or coating inspection information where specified.
- Product identification and batch traceability.
- Installation information and compatible tooling details.
Not every document is applicable to every fastener type. The project specification should determine the required inspection scope.
7. Receiving Inspection and Nonconformance Handling
Even when the purchasing specification is complete, incoming components still need to be matched to the approved order.
The receiving team should verify the relationship between the purchase order, product identification, drawing and supporting documents.
Suggested Receiving Inspection Checklist
| Checkpoint | Evidence | Action if Information Is Missing or Different |
|---|---|---|
| Part number | Package label and purchase order | Hold and clarify |
| Product type | Visual identification and drawing | Hold if construction differs |
| Dimensions | Agreed dimensional inspection | Record and assess deviation |
| Material | Certificate or specified verification | Request missing evidence |
| Surface condition | Finish specification and inspection | Record visible differences |
| Batch identity | Lot and package identification | Preserve traceability and investigate |
| Approval status | OEM or engineering approval reference | Do not release an unapproved substitute |
For quality-related enquiries, buyers can review Flybear’s fastener quality inspection information.
Available inspection categories include dimensional inspection, hardness testing, tensile testing, material analysis and surface-related checks. The actual inspection scope must be confirmed against the product and purchase specification.
Keep Nonconforming Candidates Separate
If a proposed replacement does not match the approved specification:
- Identify and segregate the affected material.
- Record the relevant part number and batch.
- Document the difference.
- Notify the responsible purchasing and quality personnel.
- Obtain the required engineering or OEM disposition.
A visually similar fastener should not be released simply to avoid a procurement delay.
8. Frequently Asked Questions
Q1. Can a structural repair fastener be replaced with one of the same diameter?
Not automatically. Diameter is only one specification parameter. The product geometry, material, installation process, mating components and OEM approval must also be considered.
Q2. Can an aftermarket rivet replace an original structural rivet?
Only when the applicable vehicle repair procedure or authorized technical approval permits it. Some manufacturers specify original or approved fasteners and installation tools for particular repair locations.
Q3. Is a higher-strength fastener always a better replacement?
No. A higher nominal strength does not establish compatibility with the original joint. Material, geometry, ductility, installation behavior and other design requirements may differ.
Q4. Can a structural rivet be installed using a different tool?
Tool compatibility must be confirmed against the approved fastener and repair procedure. A different tool should not be assumed to reproduce the required installation result.
Q5. What should a supplier provide when quoting a replacement fastener?
Provide the original part number, drawing, dimensions, material, finish, mating component information, quantity and required inspection documents. The supplier should clearly identify any differences between the candidate and original specification.
Q6. Does a supplier’s material certificate prove that a replacement fastener is OEM approved?
No. A material certificate supports material identification and specified material requirements. It does not independently establish OEM approval or validate the complete structural repair.
Conclusion: Verify Approval Before Replacing Structural Repair Fasteners
Structural repair fastener substitution is an engineering and procurement decision, not simply a dimensional purchasing exercise.
Matching the original diameter, length or nominal strength grade does not establish that a replacement fastener can reproduce the original joint.
For automotive repair procurement teams, the correct approach is to identify the original OEM part, compare the complete specification, document differences and obtain the required technical approval before releasing the replacement for use.
Looking for standard or drawing-based industrial fasteners?
Flybear supports enquiries for standard fasteners, special fasteners and drawing- or sample-based custom components. Product specifications and inspection requirements can be discussed against the actual application and purchasing documents.
Visit Flybear Automotive Fastener Applications to explore the relevant product application range.
For a technical enquiry, share the drawing, original part number, material, dimensions, surface finish, quantity and inspection requirements through the Flybear RFQ page.
Drawings, BOMs and specification attachments can also be sent directly to biz@chinaflybear.com.
Important: A Flybear quotation or technical comparison does not constitute OEM authorization for a safety-related vehicle structural repair. The vehicle manufacturer or authorized repair engineering authority remains responsible for approving the repair method and replacement parts.








